How To Repair Pool Cue Tips

Posted by : .(JavaScript must be enabled to view this email address)

Replacing a Pool Cue Tip: six Easy Steps to do it Yourself

It's like a bad dream. Your tip is worn out, you have a tournament coming up and you lot can't get to your local cue repair guy, or maybe there isn't a cue repair guy in your area at all! Well today is your lucky 24-hour interval! Today we are going to learn how to install a new tip on your cue using the Tweeten Cue Tip Repair Kit . This is something every pool player should know. Let's become started.

The film beneath shows our poor, worn out tip. This tip is pretty low and in danger of being both detrimental to your game and mayhap even damaging your ferrule.

This is what a worn out pool cue tip looks like. If your tip looks similar this (or worse), and then it'southward time to replace it!

Step 1: Remove the Old Puddle Cue Tip

The commencement stride is to remove the old tip. To practise this, y'all will need a nice sharp razor blade (delight be conscientious folks, it's hard to explicate how you cut off your finger irresolute your cue tip). Try and get as close to the ferrule every bit you tin. This may accept a few passes with the razor blade. Only accept your fourth dimension and slowly remove any leather and excess gum as seen in the sequence below.

Be extra careful removing your erstwhile tip and then you lot don't gash the side of the ferrule or your fingers.

Step 2: Clean the Pool Cue Ferrule

One time you lot are satisfied with your job removing the erstwhile tip you need to make sure the top of the ferrule is clean and as flat every bit possible. To do this y'all will at present utilize the rapid top sander included in the repair kit. Just place the shaft against the guide as shown in the following pictures and rotate until any leftover dirt and glue are removed from the meridian of the ferrule. Exist certain to continue the sander dainty and level.

A clean, flat ferrule surface is crucial for the mucilage to hold properly. The rapid elevation sander in the Tweeten Repair Kit performs this footstep perfectly.

Step iii: Fix the Puddle Cue Tip

Preparing the tip is the adjacent pace in the process. To practice this, have your favorite tip and use a piece of sandpaper to crude up the glue side of the leather. I do this past laying the sand paper on a flat surface to make certain as I sand the dorsum of the tip I keep it perfectly flat and level. Sand the tip until it is prissy and crude. It is important to brand sure the tip is roughed upwards and so the glue has something to adhere to. Apply the supplied tip cement or your favorite adhesive (I as well recommend any type of gel super glue) to the tip.

Roughing up the bottom of your new puddle cue tip is a good way of making sure the glue has somewhere to grab. Make certain to put some mucilage on the ferrule side, too!

Step iv: Place the Puddle Cue Tip on the Ferrule

In the post-obit sequence, y'all will come across the next step is to place the tip on the ferrule. Make sure to get the tip centered every bit best you can. Press firmly on the tip to brand sure whatever air pockets are removed; the glue will push out onto the ferrule. While property the tip in place, use some paper towel to wipe the mucilage that has now no doubtfulness gotten on the ferrule. The more we tin get off the ferrule now the less y'all take to worry nearly trying to sand off later. Adjacent, assemble the tip clamp that came with your kit. This clamp slips over the shaft and every bit you can see in the photo, you simply place the safe ring on the heart of the tip and pull the clamp down. Use the slider to agree the clamp in place. Allow the glue dry for 10 to 15 minutes.

Middle the tip, press down, and wipe off the excess glue. Then apply the tip clench to go along pressure while the glue sets for 15 minutes or longer.

Step 5: Cut and Sand the Cue Tip to the Ferrule

The side by side step is the part that requires a petty patience and some practise—cut the tip to match the diameter of your ferrule. I similar to identify the shaft on a hard surface with the tip downward every bit shown below. Use your razor bract to slowly shave abroad the sides of the tip. Don't try to accept off too much leather at once, it is easier to move slowly. When you go closer you can employ your ferrule equally a guide. Make sure you cut downwardly towards the table in as direct a line as you can. On a side note, don't exercise this on your kitchen/dining room tabular array….wives and or mothers do not appreciate pocket-size razor cuts in the finish. Don't ask me how I know this. Once you take the tip the same diameter as the ferrule, you can clean it upwardly some more and remove whatsoever flat spots from the razor blade using a piece of 800 grit sand paper. Be careful not to sand too much on your ferrule.

Again, be extremely cautious with this step so you can avert damaging your pool cue ferrule. Use a high grit sandpaper to get that terminal piece of the tip perfect.

Step 6: Shape the Pool Cue Tip

So now you have a tip glued firmly on and the same bore every bit your ferrule, but it is probably apartment. Fourth dimension to shape it upward. Utilise your favorite tip shaper, or the shaper that comes in the kit. Sand the tip until you get the desired shape yous prefer, dime, nickel etc. In one case y'all have the tip shaped upward, moisten the side of the tip (a footling water works fine, but don't get information technology likewise wet). Use a prissy slice of leather to brighten the sides of your tip, below shows the Pooldawg Tip and Shaft Burnisher .

Burnishing the side of the tip gives it a smoothen finish and helps information technology to hold its shape.

We now accept our finished tip. Non everyone has access to a good cue repair person or even the utilise of a lathe to install tips, just there is no reason to worry now that you lot know how to put your ain tips on. Your first attempts might be a footling rough, only in time you will develop your own methods and your tip installs volition improve.

Here is the final product. Try information technology yourself and you'll see that it'southward easier than you think to alter your own pool cue tip.

Until next time.

Mikey V.

• RELATED Manufactures
• How to Modify a Pool Cue Tip – By Florian "Venom" Kohler
• Shaping your Pool Cue Tip – By PoolDawg Staff
• How to Choose the Right Pool Cue Tip – By Mikey Verkruyse

Source: https://www.pooldawg.com/article/pooldawg-library/replacing-a-pool-cue-tip

Posted by: carsonveackell.blogspot.com

Share this post